產品簡介
關鍵詞：SLK,SSLK-25A,SSLK-8A,滑塊定位器,美式,
滑塊定位器 SSLK-8A：
美式標準滑塊定位器的設計，有效的預防模座滑塊逐漸鬆動的問題。
外型小巧，利用了有限的空間。
滑塊定位器SSLK-25A：
容易安裝進模座滑塊中，
隱藏在定位裝置中。
關鍵詞：CBS50X100L14,PROGRESSIVE,TGU25,UCU87,Unilifter,
The Unilifter system is the most widely used standard product for molding and releasing undercuts.Smooth performance is attained due to the U-Coupling design,eliminating wear and binding found in other fixed angle lifter designs.
關鍵詞：DACC,DateMarkedPi,凸型,日期章,西班牙式,
日期章(西班牙式標準系列)-凸型此產品分為兩種規格，
其他尺寸可接受客人要求訂作。
關鍵詞：DACA,DateMarkedPi,一般型,日期章,西班牙式,
日期章(西班牙式標準系列)-一般型此產品分為八種規格，
其他尺寸可接受客人要求訂作。
關鍵詞：10M,20M,40M,MRT型,SMRT,滑塊定位器,美式,
滑塊定位器(美式-MRT型)分為三種規格：
SMRT 10M 、 SMRT 20M 、 SMRT 40M
其他尺寸可接受客戶要求訂作。
關鍵詞：AV-08,AV-12,AV-18,PROGRESSIVE,VALVES,AIR,
Progressive Air Valves reliably break the vacuum created when molding deep draw parts,such as containers and buckets.
Material: 420 Stainless Steel,with TiN coated plunger
Hardness:50-55 Rc
Pressure Required:29-140 psi
Maximum Mold Temp:450 ° F
關鍵詞：PSL,PSL0001,PSL0002,滑塊定位器,美式,
滑塊定位器(美式)分為三種規格：
SPSL0001 、 SPSL0002 、 SPSL0003
其他尺寸可接受客戶要求訂作。
關鍵詞：CA-100,CAMM-100,CamAction,PROGRESSIVE,滑塊定位,
The CamAction reliably pulls mold details while reducing extreme conditions associated with angle pins and sideaction.The efficient design eliminates machining to the cavityhalf and reduces mold base size and installation time compared to previous methods.
Travel = .160"(4mm)
All CamAction parts are hardened and treated for wear resistance
關鍵詞：1325,1337,250,250F,251,251-BSPT,251F,252,252-BSPT,
Progressive Connector Plugs can be easily attached to any length pipe nipple or brass extension or threaded directly into the mold base or insert.
關鍵詞：SRTM-13,SRTM-36,Slide,定位珠,Retainers,SRT-10,SRT-30,
Progressive's new SRT Series Slide Retainers reliably hold side actions from 10 to 80
pounds (4 to 36 kgs). The new slide retention design features Friction FreeTM technology for
smooth operation, especially in clean room or greaseless environments.
The compact
design allows for installation in the mold base or wear plates.
The installation shown at left is typical for all
Retainers and Cleats. However, if not utilizing the
optional cleat, a V-groove or ball cut can be
machined as shown in the graphics at right.
On the slot width, the cutter clearance must
exceed the "D" dimension.
Technical Information:
• Maximum operating temperature is 425° F (218° C).
• The roller is through hardened stainless steel and the axle is nitrided stainless steel.
• For P-20 slides, a Cleat is suggested versus adding a detent in the slide.
• Retainers and Cleats are sold separately and include all required screws.• Replacement items are available. Refer to price list for catalog numbers and pricing,
and contact Customer Service for availability.
關鍵詞：SLR100X400,SLR50X125,SLR50X150,SLR50X150-L,SLR50X2
Technical Information:
• Bearing Cage Material: Chemical resistant, high impact, glass-filled Nylon
• Bearings: 64 HRC
• Maximum Mold Temperature: 300° F (150° C)
• Engagement occurs at E dimension shown.
• Locks are to be mounted in the mold base and not in the core or cavity inserts.
• For optimal performance, pockets are to be machined to nominal “W”
pocket width dimensions in each table. If replacing locks in existing pockets,
ensure .0004” clearance, and the lock may be modified to suit.
• As with other mold mechanisms, clean and maintain locks at the molds scheduled PMs.
Shuttle Lock sets and special configurations are also available. Contact Customer Service for more information.
關鍵詞：CC-125-PC,CC-150-PC,CC-175-PC,CC-200-PC,CCM-0001,C
The RT Series Collapsible Cores are available in sizes to fit most inside detail applications. Whether molding
threads or complex details, these cores can simplify design and production. Collapsible Cores allow for
smaller molds to run faster cycles with less moving parts.
關鍵詞：DACD,DateMarkedPi,日期章,綜合型,西班牙式,
一個組件由年、月、日和班指組成，應用於生產控制中。
可以是其他任意組合，包括預留雕刻位置。
關鍵詞：GS,Standard,Type,西班牙式,開閉器,
專為分段開閉的模具設計，可精確調整板模在不同區段與距離，進行開閉的動作。
可安排開模的先後順序。
關鍵詞：EGS,EGS-8,ESG-10,射梢斜座,萬向滑座,
射梢斜座(萬向滑座)此產品規格分為十種：
EGS-8 、 EGS-10 、 EGS-12 、 EGS-16..等
其他尺寸可接受客戶要求訂作。
關鍵詞：APN06,APN12,APN25,APN37,APN50,Adjustable,HEX,Nippl
Progressive Adjustable Hex Nipples utilize pre-cut, standard pipe threads on both sides of the hex for easy adjustments.
關鍵詞：PROGRESSIVE,TL112,TL175,TL75,TopLocks,
Progressive Top Locks provide positive guidance between cavities and cores and will not bind due to unequal thermal expansion of the mold halves. Top Locks have large corner radii and are designed for standard plate thicknesses for easy machining and installation from parting line.
Materials and Treatments:
Females: A-2,58-60 Rc
Titanium Nitride Coated(80 Rc)
Male: H-13,40-44 Rc
Melonited(SBN) to 65 Rc
關鍵詞：Locks,TLR112X200,TLR150X250,TLR150X250-L,TLR87X150
Technical Information:
• Bearing Cage Material: Chemical resistant, high impact, glass-filled Nylon
• Bearings: 64 HRC
• Maximum Mold Temperature: 300° F (150° C)
• Engagement occurs at E dimension shown.
• Locks are to be mounted in the mold base and not in the core or cavity inserts.
• For optimal performance, pockets are to be machined to nominal “W”
pocket width dimensions in each table. If replacing locks in existing pockets,
ensure .0004” clearance, and the lock may be modified to suit.
• As with other mold mechanisms, clean and maintain locks at the molds scheduled PMs.
Shuttle Lock sets and special configurations are also available. Contact Customer Service for more information.
關鍵詞：HFC1414,HFC14141,HFC1616,HFC1818,HFC18181,HFC3814,
Progressive High Flow Cascades utilize an offset design,providing all connecting pipes a full thread sealing area while preventing pipe interference.Pipe Plugs are eliminated, and the thin-walled stainless steel tube improves flow rates by 35-65% over standard cascades.
Materials:High Flow Head:Brass
12"Long High Flow Tube:Stainless Steel
2"Long Pipe Nipple:Galvanized Steel
關鍵詞：CVPL-100,CVPL-200,CounterView1,PROGRESSIVE,方形計數器,
Progressive CounterViews positively monitor mold usage by tracking activity for the life of the tool.Three mounting styles are available for easy installation of the CounterView.
Material: Glass-filled Nylon housing
Maximum operating temperature is 250 °F(120 °C)
Counter: Non-resettable mechanical,7-digit
U.S.Patent Number 5,571,539,others pending
關鍵詞：AJV,GVA,氣動頂針,空氣梢,美式,
氣動頂針(空氣梢-美式)此產品規格分為三種：
AJV-DME08 、 AJV-DME12 、 AJV-DME18
其他尺寸可接受客戶要求訂做
關鍵詞：RC,SRC.123006,SRC.164008,滑塊定位器,西班牙,
只需要很小的空間就可以安裝固定。
滑塊定位器(西班牙式-RC型)規格分為六種：
SRC.123006、SRC164008..等。
關鍵詞：BAFFLES,BRASS,PROGRESSIVE,SB06L4-24,SB100L4-24,TB0
Progressive Baffles are constructed by precisely silver brazing brass blades to the highest quality forged brass pressure plugs.Turbo Baffles ease installation and removal,while improving cooling balance by the generation of turbulent coolant movement.
Material: Brass
Standard flush-seal type plugs used (7/8''taper per foot)
Baffle orientation slot provided
關鍵詞：1/16,1/2,1/4,1/8,3/4,3/8,PROGRESSIVE,PipePlugs,
Progressive Pressure Plugs are premium quality forged to meet consistent and accurate installation requirements.Standard plugs are flush type,7/8"taper per foot.
Materials:Brass,Alloy Steel,&Stainless Steel
Oversize Plugs available with 3/4" taper per foot
關鍵詞：Block,LK-15,LK-25,LK-45,Locating,Sets,立式固定塊,
Male
YK30
HRC 50 ° ~ 55 °
Female
YK30
HRC 55 ° ~ 60 °
關鍵詞：GL100,GL150,GL200,GL250,GuideLocks,PROGRESSIVE,
Progressive Guide Locks provide positive guidance between cavities and cores and will not bind due to unequal thermal expansion of the mold halves. The three-piece design allows for easy installation and fitting of inserts.
Materials and Treatments:
Females(2):H-13,40-44Rc
Melonited(SBN) to 65 Rc
Male: A-2,58-60 Rc
Titanium Nitride Coated(80 Rc)
關鍵詞：251,252,253,350,351,352,353,354,553,554,EP250,Exte
Progressive Extension Plugs are designed to eliminate the installation problems with previous practices of soldering and welding connector plugs to steel pipe nipples. Precision machined taper conforms to industry guidelines to provide a leak-free fit with tapered inlets
關鍵詞：DACB,DateMarkedPi,三層型,日期章,西班牙式,
模具中需要兩種不同的指示使用此款產品，不需要兩個日期章，
由12組月份6組年份組成，訂購時請具體標註所需年份。
關鍵詞：CVR-18,CVR-23,CVR-28,CVR-33,CVR-38,CVR-43,CVR-83,C
The new R-Series CounterView provides the innovative in-mold cycle counter teachnology engineered by Progressive ,now allowing for easy installation from the back of the A or B plate.
Maximum operating temperature is 250°F (120°C)
Counter: Non-resettable mechanical, 7-digit
U.S.Patent Number 5,571,539,others pending.
Available in left-hand and right-hand versions,for both inch and metric nominal plate thicknesses.
關鍵詞：PROGRESSIVE,SL100X137,SL50X87,SL75X137,SL75X187,Si
Progressive X-Series Side Locks provide positive guidance between cavities,cores,and stripper inserts.Pockets are machined on the side with the mold halves assembled.The dissimilar steels,heat treated to different hardnesses,protect galling or wear and binding due to unequal thermal expansion of the two halves of the mold.
Materials and Treatments:
Females(2):A-2,58-60 Rc
Titanium Nitride Coated(80 Rc)
Male: H-13,40-44 Rc
Melonited(SBN) to 65 Rc
